Mounting Hole Spacing of Replacement CE Smith Vertical Bunk Bracket

Question

Question:

How wide and how wide are the two holes apart.?

asked by: Martin

0

Expert Reply:

In regards to the Replacement CE Smith Vertical Bunk Bracket part # CE10160A40, the frame mounting holes are 3-9/16" apart and the bunk board mounting holes are 1-1/2" apart. I have attached a photo below.

expert reply by: Conner L

0

Mounting Hole Spacing of Replacement CE Smith Vertical Bunk Bracket
(click to enlarge)

Answer 1

There are some mounting holes started on the sides of the Yates Keel Pad #YR1203SB. You simply need to acquire mounting hardware from your local hardware or home improvement store to mount these on the crossmember of your boat trailer. Mounting…

view full answer...

Answer 2

The closest metric trailer tire size to a 4.80x12 is going to be a 145/80-12. The typical diameter of a 4.80x12 tire is 20.5 inches. On a 145/80-12, it is 21.3 inches. So the metric size will be a little over 1/4 inch taller. Make sure to measure the…

view full answer...

Answer 3

It looks like the Single Axle Trailer Fender #PF775X21W is the same fender you have on your trailer. I went out into our warehouse and measured the distance lengthwise between the mounting holes of the fender and found it to be 18 inches.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Mounting Hole Spacing of Replacement CE Smith Vertical Bunk Bracket

Product Page this Question was Asked From

Continue Researching