Will Thule Hullavator Pro Kayak Carrier Fit Rhino-Rack Square Crossbars

Question

Question:

Will the Thule hullavater fit on the rhino square bars? Alternatively if not, are 65 inch bars available from Thule? Thanks

asked by: James P

1

Helpful Expert Reply:

Yes, the Thule Hullavator Pro Kayak Carrier # TH898 will fit your Rhino-Rack square crossbars. Just make sure that you're able to have the 4"-8" of overhang for the towers so the Hullavator doesn't contact your vehicle and you'll be good to go!

expert reply by: Jon G

1

Answer 1

Yes, the Thule Hullavator Pro Kayak Carrier part #TH898 will work with the Malone AirFlow2 Roof Rack either using the integrated channels or the wrap-around style clamps. However, the Hullavator requires that the crossbars extend at least 4"…

view full answer...

Answer 2

There are a few limitations when installing the Thule Hullavator Pro Kayak Carrier and Lift, #TH898. The carrier will fit square and most crossbars with top channels in the crossbar. The crossbars must have a minimum spread of 24 inches. This is…

view full answer...

Answer 3

The Thule Hullavator part #TH898 takes up approximately 28.5 inches of cross bar space so you would need at least 57 inch bars, therefore the 65 inch bar you mentioned will work. Keep in mind that the Hullavator requires 4-8 inches of cross bar…

view full answer...

Answer 4

In order to use the Thule Hullavator Pro Kayak Carrier and Lift Assist part #TH898 on a 2020 Subaru Outback you will need an aftermarket roof rack because the factory roof rack does not have the needed crossbar overhang. For this, I recommend the…

view full answer...

Answer 5

There are two ways to connect the Thule Hullavator to your crossbars, clamp on or use the T-slot. Clamp on requires square bars and T-Track requires a Thule Crossbar. If you have raised side rails on your vehicle, the SteelTop #MPG203 will just clamp…

view full answer...

Answer 6

Thank you for all of the information! While you are able to use the Hullavator #TH898 with your setup as far as weight goes, this kayak carrier does require the crossbars to stick out 4" - 8" out past the roof rack feet. Since the Thule…

view full answer...

Answer 7

For the roof rack on your 2013 Honda Pilot, I recommend the Yakima CoreBar Crossbars - Steel - Black - 60" Long - Qty 2 #Y00422 along with the TimberLine Towers for Yakima Crossbars - Raised, Factory Side Rails - Qty 4 #Y33TR. This will give you…

view full answer...

Answer 8

The Thule Hullavator #TH898 requires a set of aftermarket crossbars that extend past the feet of the rack 4 to 8 inches. I tried to find a roof rack for your 2017 Inifiniti Q60 that would work or find info on the factory rack but could not find…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 11

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...