Will Brophy 5 Gallon Bucket Holder for E-Track Hold 5 Gallon Bucket of Water

Question

Question:

If the e track is welded, will this hold a five gallon bucket of water?

asked by: Jacob

0

Expert Reply:

Yes, the Brophy 5 Gallon Bucket Holder for E-Track # ETBHB will indeed hold a 5-gallon bucket of water.

I have added a link below to a video review for you to check out as well of the Bucket Holder # ETBHB.

expert reply by: Kyle S

0

Answer 1

Absolutely, the Brophy 2-Slot Horizontal E-Track can be used as an anchor point to hold down the tires on your ATVs. They have a safe working load limit of 1,000lbs, so that would be more than enough for your ATVs. You'll need straps to secure…

view full answer...

Answer 2

When the jack #TJDA-5000S is fully retracted you will have a measurement of 7-1/8 inches from the bottom of the mounting plate to the bottom of the foot plate and when fully extended that measurement is 22-3/8 inches. From the top of the jack to the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Will Brophy 5 Gallon Bucket Holder for E-Track Hold 5 Gallon Bucket of Water

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching