Can Dexter Brake Assemblies 23-180-181 Work in Place of 23-105-106

Question

Question:

Good morning , I have a enclosed trailer with 6000 LB axles and was going to purchase new brake assy. part # 23-105-106 Was wondering if the 23-180-181 would work in place of them? Because the 23-105-106 will work on 5200-7000 trailers. Thank you

asked by: Steve Q

0

Expert Reply:

Yes the Dexter brake assemblies part # 23-180-181 would work in place of the # 23-105-106. They are the same size and the capacity range matches as well.

expert reply by: Jameson C

0

Answer 1

You can convert your trailer to electric over hydraulic brakes by using hydraulic trailer brakes, hydraulic drums, hydraulic brake lines, and adding an electric over hydraulic actuator like the HydraStar Electric Over Hydraulic Actuator for Drum…

view full answer...

Answer 2

In order to convert a trailer from hydraulic drum brakes (023-324-00 and 023-325-00) to electric drum brakes you can use the Electric Trailer Brake Kit part #AKEBRK-6. The hubs/drums can be reused but you will need to update the wiring using the…

view full answer...

Answer 3

The Dexter Electric Trailer Brake Kit #23-180-181 comes with a left hand and a right hand assembly. If you are needing 4 assemblies you will need to purchase 2 sets of this kit. You can check out the assemblies in the review video I linked for you.

view full answer...

Answer 4

The difference between the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs #23-180-181 and the #23-105-106 you mentioned are the strength of the brake magnets. The #23-180-181 was designed for 7000lb axles…

view full answer...

Answer 5

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Can Dexter Brake Assemblies 23-180-181 Work in Place of 23-105-106

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching