Picking Out Replacement Brake Assemblies for 2003 Fleetwood Prowler Lynx

Question

Question:

Im trying to figure out which drum brake replacement is needed for my 2003 Fleetwood Prowler Lynx 830Y. All I know is that it has 14inch tires.

asked by: Kelly M

1

Helpful Expert Reply:

To pick out the correct brake assemblies for your trailer you need to know a few things but I do not have ability to look up what your trailer would have had.

You will want to measure the inner diameter of your hub/drums and the depth of the drums to determine what brake assembly dimensions you need. For example the part # 23-26-27 is a 10 inch by 2-1/4 inch thick brake assembly.

You also want to determine what the bolt pattern is of your assembly mounting flange. The standard size is 4 on 4 inch. You also want to determine the axle capacity of your trailer and go with an assembly that has the same rating, the # 23-26-27 has a 3,500 lb capacity.

expert reply by: Jameson C

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Hey Eric! Are you wanting to change from disc brakes to electric hub and drums, or are you just wanting to replace the rotors themselves? Traditionally 10" brakes are only compatible with up to 15" wheels but if yours have been working just…

view full answer...

Answer 6

Picking out brake assemblies for trailer axles is actually pretty easy but I am not able to determine the info I need from your trailer info since it's not something manufacturers keep records of. You do need to order a total quantity of 4…

view full answer...

Answer 7

For replacement Dexter manual adjust brake assemblies to replace your 36-19 you would want the part #23-27 for the right hand side and part #23-26 for the left hand side. These are manual adjust 10 by 2-1/4 inch Dexter brake assemblies that would…

view full answer...

Answer 8

Hey Erik, so if the coupler on your 2007 MasterCraft boat trailer is labeled a UFP or a Dexter actuator and looks like the #DX99FR then yes this inner member is correct replacement to get it working again. There isn't a way to look up what your…

view full answer...

Answer 9

The Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 5-1/2 #AKHD-555-35-K will fit the spindle on your trailer to replace your AL-KO 8700 hub, but this does have a 5 on 5-1/2" bolt pattern. My information is the AL-KO…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Picking Out Replacement Brake Assemblies for 2003 Fleetwood Prowler Lynx

Product Page this Question was Asked From

Continue Researching