How To Find Correct Replacement Taillight for Winnebago Minnie Winnie

Question

Question:

Is this the replacement part for rear tail light assembly for 2016 Mini Winnebago, part#183787-01-000?

asked by: John C

1

Helpful Expert Reply:

The Triple LED Trailer Tail Light part # CE44VR is a pretty common OEM taillight used on motorhomes so as long as the style is the same as the one you have and the dimensions of 14" long x 6-7/8" tall x 1" deep are the same it should work great as a replacement.

Unfortunately, we can't cross-reference Winnebago part numbers but they may be able to give you the taillight manufacturer part number and in which case we could then likely confirm.

expert reply by: Conner L

1

Answer 1

Sorry for any confusion Aaron, I can confirm that the 22" Wide Vent Hood #VE78SR is 18" deep as you can see in the picture below.

view full answer...

Answer 2

We do not have a 4-way to 4-way adapter with the diodes that stop the hyper flashing. You can install load resistors like part #DI34ZR. You would install the load resistors on the affected circuits. I have attached a drawing that shows how the…

view full answer...

Answer 3

I wasn't able to find the dimensions or really any info on your PH-1 20 so you'll want to verify a few things before purchasing the Ventline Pinnacle Ducted RV Range Hood with Light #VE78SR. The first one being size, this fits in a…

view full answer...

Answer 4

The iRV RV Stereo #IRV64FR would easily fit in place of the RV stereo you have installed in your 2020 Winnebago Micro Winnie as it was designed for fitting in place of standard RV stereos. This does not have an SD card input but in general you…

view full answer...

Answer 5

Yes, I confirmed with my contact at Command Electronics that the Triple LED Trailer Tail Light - Stop, Tail, Turn, Backup - Red and Clear Lens #CE44VR is a direct replacement of your OEM tail light on your 2018 Thor Four Winds 30D Motorhome. I went…

view full answer...

Answer 6

Since your RV currently has incandescent lights and you're going to be replacing them with Triple LED #CE44VR you will need to add resistors like the Putco LED Light Bulb Load-Resistors - Aluminum - Qty 2 Item #P230004A-2 to the turn signal…

view full answer...

Answer 7

That's a good question, and the answer is yes, the improved version is in fact the Triple LED Trailer Tail Light - Stop, Tail, Turn, Backup - Red and Clear Lens #CE44VR. This is the updated replacement of the 003-30LEM2, but with a much better…

view full answer...

Answer 8

I've linked to a diagram showing the dimensions of the Command #CE44VR trailer lamp. We don't have a video completed as of yet, but when we do, it'll appear on the website.

view full answer...

Answer 9

If your RV currently has incandescent lights and you're going to be adding the Triple LED #CE44VR to the mix then you will most likely need to add resistors like the Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2 #DI34ZR to the…

view full answer...

Answer 10

Since they are on the same circuit, you will want to switch the running lights to LED as well when installing the #CE44VR. Mixing the two has a tendency to cause problems with the lights functioning, and it is definitely important to have working…

view full answer...

Answer 11

I don't believe they're considered true OEM replacement tail lights for your Class A, but I do know that some of our neighbors have successfully used the Triple LED Trailer Tail Light #CE44VR on their RVs. You'll want to confirm that the…

view full answer...

Answer 12

The Diamond LED Light Bulb Load-Resistors #DI34ZR are designed to fix the hyperflashing you are experiencing though they do need to be installed on the circuits of the affected lights. You are going to need to determine if those circuits are…

view full answer...

How To Find Correct Replacement Taillight for Winnebago Minnie Winnie

Product Page this Question was Asked From

Continue Researching