Does the Advent Air Replacement for Coleman Setup Use the Existing Air Distribution Box and Controls

Question

Question:

I have a Coleman Mach 8 Plus 15K BTU Air Conditioner w/ Heat Pump and Condenser Pump in Black that when bad. to install the accol150b do you still use the coleman control board.

asked by: Jim J

0

Expert Reply:

When installing the Advent Air Replacement RV Air Conditioner for Coleman Setup w/ Start Capacitor - 15,000 Btu - Black # ACCOL150B it will plug right into your existing air distribution box that has controls built in, which I believe is what you're referring to when you say the control board. This is designed to put to use the existing components from your Coleman AC, so it's a plug and play replacement.

expert reply by: Erik B

0

Answer 1

From the information you have provided, it sounds like you most likely have the MaxxAir MaxxFan 4751KS. If that is indeed the case then the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS would be the correct…

view full answer...

Answer 2

It does sound like you need a new circuit board for the 4951KS that you have based on what you described from your vent. So for that you'd want the part #MA10A04751KS and you'd be set.

view full answer...

Answer 3

If you have the MaxxFan Plus vent the correct circuit board is the part #MA10A04751KS that you referenced.

view full answer...

Answer 4

The Replacement Key Wall Control #MA00A03550K is used to control the MaxxFan 4951 vent fan.

view full answer...

Answer 5

Thanks for reaching out! Since you have the 4951KS model MaxxFan roof vent you'll need the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS. The circuit board might look slightly different as far as the pieces…

view full answer...

Answer 6

This definitely sounds like the circuit board, so you'll want to use the Replacement Printed Circuit Board #MA10A04751KS which is designed to work with models 4751KS, 4761KS, and 4951KS. I know some other customers have been apprehensive about…

view full answer...

Answer 7

My contact at MaxxAir advised that there are three potential causes for the beep and no fan motion you're experiencing with your MaxxFan Trailer Roof Vent #MA00-04000K. One potential cause is that the unit was wired with incorrect polarity. Make…

view full answer...

Answer 8

The issue your MaxxFan Plus Roof Vent 4951KS is having is a tell tale sign of a bad circuit board. What I recommend is first completely unplugging the circuit board, as it has a built in lock that gets engaged under certain conditions and makes it…

view full answer...

Answer 9

Since you've already changed the motor and your vent lid still won't lift, it sounds like the issue is the operator mechanism. You can replace that with the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents…

view full answer...

Answer 10

The MaxxFan Plus Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke #MA00-04500K is the similar fan to the 4951ksc. The issue you are having with the fan and lid are likely the circuit board which can be replaced with…

view full answer...

Answer 11

The issue you are having with your MaxxAir MaxxFan 4751KS is more than likely an issue with the circuit board (control board). The circuit board is what is telling the motor to run or stop. The correct replacement circuit board for your MaxxAir…

view full answer...

Answer 12

It definitely is the circuit board of your MaxxAir roof vent and the correct replacement is the part #MA10A04751KS.

view full answer...

Does the Advent Air Replacement for Coleman Setup Use the Existing Air Distribution Box and Controls

Product Page this Question was Asked From

Continue Researching