What MORryde Steps Will Fit On My 2016 Grand Design Reflection 5th Wheel.

Question

Question:

Looking to buy a set of steps for my 2016 Reflections 337RLS the height is 36” the flange opening is 28 1/4” would like the 4 step strut assist can you recommend a mode number so I can include in my pending order ?

asked by: Paul L

0

Expert Reply:

To get the four steps you need the MORryde StepAbove Strut Assist Fold-Down Step for 27-3/4" - 28-1/4" RV Door Frame - Quad # MR85RR is the way to go. The legs are adjustable and they have foot pads that move independently to give you stability on uneven surfaces.

expert reply by: David B

0

Answer 1

Both ends of the tube for the MORryde RV Door Latch Extender #MR22JR are threaded so you wouldn't be able to cut it shorter to accommodate your trailer's handle. I had this same issue when I first installed this when it came out, but…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 5

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 6

We still recommend the use of a slider in all standard/short bed trucks. That being said, the new GM trucks like your 2022 GMC Sierra 2500 do have a slightly longer bed than the typical standard bed. The best thing you can do is to measure to see…

view full answer...

Answer 7

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from…

view full answer...

Answer 10

Yes, you are going to also need the Demco Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 when using the Demco Autoslide 5th Wheel Trailer Hitch w/ Slider #DM8550040 with your Road Armor pin box. For a suspension enhancement I…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...