Correct Replacement Cover for TruXedo Lo Pro Tonneau Cover on a 2013 Toyota Tundra with 5.5 Bed

Question

Question:

I need the truxedo lopro replacement cover part number for my 2013 Toyota Tundra crewmax. When I put my vehicle info in it doesn’t ask to specify long or short bed when pulling up the cover nor does it state anywhere in the description what size the cover is that says will fit my vehicle.

asked by: Frank L

0

Expert Reply:

The correct replacement tarp or cover for the TruXedo Lo Pro Soft Roll-up Tonneau Cover on a 2013 Toyota Tundra with 5-1/2' or 5' 6" bed is part # TX5637-CVR or part # TX5638-CVR for models with the deck rail system.

expert reply by: Conner L

0

Answer 1

The correct Replacement Cover for TruXedo Lo Pro Soft, Roll-up Tonneau Covers for a 2007 Toyota Tundra CrewMax is part #TX5638-CVR if you have the deck rail system or part #TX5637-CVR if you don't.

view full answer...

Answer 2

Thank you for the images Barb, but you are going to have to take a couple measurements to verify what is going to work best for your exact situation. It looks like you have a 2019 Toyota Tundra with the B&W Turnoverball Underbed Gooseneck Trailer…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

You can certainly go ahead and re use the existing 2 bolts, provided they are in good condition. The fish wire method shown in the video works too, but it is also very common to just use the two bolts like your old Atwood actuator. Personally I would…

view full answer...

Answer 5

Two bolts will be sufficient for installing the Demco Hydraulic Brake Actuator #DM72VR. You will want to use two Requires 2-1/2" x 4-1/2" Grade-5 of Grade-8 bolts. Personally I would use something like the Curt Coupler Hardware Kit #C25388.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 8

If you're wanting an all aluminum retractable cover with t-slots then you can use the RetraxPRO XR Hard Tonneau Cover #RTT-80841. This would be compatible with your 2019 Toyota Tundra's 5.5' bed with a deck rail system.

view full answer...

Answer 9

If you're wanting a tonneau cover with t-slots to mount accessories on for your 2019 Toyota Tundra with a 5.5' bed then you'll need the RetraxONE XR Hard Tonneau Cover #RTT-60841 if you have a deck rail system or part #RTT-60831 if you do…

view full answer...

Answer 10

the RetraxPRO MX Hard Tonneau Cover #RTX94XR is for select models from 2022-2024 so you would need part number #RT80841 instead. This is for models with a deck rail system, if you don't have one then you'll need part #RT80831 instead.

view full answer...

Correct Replacement Cover for TruXedo Lo Pro Tonneau Cover on a 2013 Toyota Tundra with 5.5 Bed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching