What is the Brake Flange Bolt Pattern on the 3,500 Pound Brakes AKEBRK-35-SA?

Question

Question:

Hello, what is the flange bolt pattern for this break kit? The info pages do not state. AKEBRK-35-SA

asked by: Jeff

0

Expert Reply:

The Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs # AKEBRK-35-SA will have the standard 4 bolt pattern used on 10" diameter 3,500 brake assemblies. This will measure 2-7/8" from center to center of the bolts/holes when going around them. I included a picture that shows what I mean by this as well.

It should be noted that the # AKEBRK-35-SA does not come with replacement nuts. If your current ones are not in the best shape, you will also need the Mounting Hardware for 10" Brake Assemblies # BRKH10B to complete the set up.

expert reply by: Lazer S

0

Standard 4 Bolt Patter - 3,500 Pound 10" Diameter Brakes
(click to enlarge)

Answer 1

There is a retainer bolt in the wheel carrier that holds the bushing and king pin in place in the Demco Kar Kaddy SS #DM9713045. You would need to remove the retainer bolt to release the king pin and replace it. This is a part that we do not…

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

The mounting holes for brake assembly #AKEBRK-35L are indeed 4 inches diagonally from the center of one to the center of the other. Side to side or top to bottom the holes are spaced approximately 2-7/8 inches apart on center. The pilot hole is…

view full answer...

Answer 4

The center diameter of the rotor of the part #K2R35S is 3.6 inches. The bolt pattern for the 4 holes of the mounting flange are of the same standard pattern for trailer brake assemblies. The bolt holes will be 2-7/8 inches left to right and…

view full answer...

Answer 5

Brake assembly mounting patterns are different than the wheel assemblies for trailers or cars. Measuring between the bolt holes on the #23-459, right hand, and #23-458, left hand, brake assemblies, the measurement is 2-1/8 inches on center for all…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

What is the Brake Flange Bolt Pattern on the 3,500 Pound Brakes AKEBRK-35-SA?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching