Can Additional Crossbar Attach to Thule TracONE Ladder Rack Load Bar

Question

Question:

I plan on mounting two extra crossbars across existing TracRac One Universal Rack. Any suggestions on how to attach them to existing crossbars? Also need four 4 End Caps for the extra crossbars. Do you stock? Whats the part number? Thanks,

asked by: Peter H

0

Expert Reply:

Sounds like you are looking for like a cantilever extension to mount an additional crossbar in front of your TracOne ladder rack.

For that you'd just need the part # TH24002XT which attaches to the current load bar and gives you an additional one mounted out in front of it.

expert reply by: Jameson C

0

Answer 1

Yes, the Erickson Over the Cab Truck Bed Ladder Rack part #EM07707 that you referenced is a confirmed fit for your 2017 Toyota Tacoma double cab long bed.

view full answer...

Answer 2

The Erickson Over-The-Cab Truck Bed Ladder Rack, part #EM07707 measures 135 inches long x 54-13/16 inches wide x 32-7/8 inches tall. This rack has a weight capacity of 800-lbs. This is an easy, no-drill installation by clamping to the bed rails of…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 6

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 7

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Answer 10

Yes, the Thule TracRac SR Sliding Truck Bed Ladder Rack #TH57RV will fit your 2020 Ram 1500 with the 5'7" bed and no Ram box. Unfortunately, this rack is only available in the silver color. We do offer the TruXedo Elevate Truck Bed Rack…

view full answer...

Answer 11

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Can Additional Crossbar Attach to Thule TracONE Ladder Rack Load Bar

Product Page this Question was Asked From

Continue Researching