How To Remove The Pin From The Inno Tire Hold

Question

Question:

Hi. I cant remove the pin. Ive been trying a few times and it remsons stuck.

asked by: Joven Y

1

Helpful Expert Reply:

There is a certain way that the Inno Tire Hold 2 # INH120 pin goes in. It has a specific shape so you will have to rotate that pin until it hits the right spot and then it'll come out no problem. I've included a video for you and around the 7:40 mark you will see what I'm talking about.

expert reply by: Adam E

1

Answer 1

Thanks so much for your purchase of the Inno Tire Hold 2 Bike Platform Rack #INH120. And that is a good question about how the rack is secured to your hitch, as it doesn't have a traditional hitch pin that goes all the way through, so I'll do…

view full answer...

Answer 2

The same hitch pin is used on the Inno Tire Hold 2 Bike Platform Rack #INH120 when used in the 2 inch and the 1-1/4 inch configuration actually. I attached a picture that shows the pin and the 2 inch adapter in relation to the shank of the rack as…

view full answer...

Answer 3

Hey Joel, we have bike racks that will work for you but the Inno bike rack part #IN25RR only fits up to 3-1/2 inch wide tires. The Kuat Piston Pro bike rack part #KU66ZR would work great as it can fit a bike tire width up to 5 inches.

view full answer...

Answer 4

Hey Ken, so the light bar part #HLY54RR that you referenced was designed specifically to fit the Hollywood Racks Destination part #HLY66ZR but I am sure if you wanted to make it work it would be possible.

view full answer...

Answer 5

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 6

Great question Gerard! The Thule Bike Adapter Bar #TH982XT could potentially pull the seat loose, but that would take either going over some pretty rough terrain for a prolonged time, or a whole lot traveling without checking on the bike. I will say,…

view full answer...

Answer 7

Any bike rack will require some degree of lifting to seat the bike within the carrier. A hitch mounted platform type rack is definitely the right choice when being concerned about lifting height; especially if you already have a hitch installed on…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

How To Remove The Pin From The Inno Tire Hold

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching