Recommended Ramps for Loading Can Am Slingshot in Toy Hauler Trailer

Question

Question:

Was thinking of 4 of the 67inch race ramps, but after seeing what was suggested for a traditional trike Im wondering if the ramp placed in the middle should be longer for the Can Am?

asked by: Deb J

0

Expert Reply:

It would be ideal if the middle ramp is longer than the two outside ramps while loading. This would ensure there are minimal ground clearance issues but there are a multitude of factors that would come into play so it's hard to predict this beforehand. I suggest the Race Ramps Trailer Loading Assist Ramps part # RR-TR-5 for the outside wheels and the Race Ramps Trailer Loading Assist Ramps part # RR-TR-7 for the center wheel.

Unfortunately, the ramps are sold as sets.

expert reply by: Conner L

0

Answer 1

While we don't carry the 10 cubic foot Furrion RV fridge I think I have a great solution for you to keep the doors shut when travelling with the Everchill 12-Volt RV Fridge Door Latch #324-000149. Once installed this will easily hold the doors…

view full answer...

Answer 2

The overall height of the Race Ramps Trailer Ramps #RR-TR-5 is 5 inches, the length of the ramp is 67 inches, and the angle of the ramp is 4.3 degrees. Your vehicle that sits 5-1/2 inches off the ground would easily fit without scraping. If your…

view full answer...

Answer 3

The longer the ramp, the less likely it is to drag or scrape. Ideally we have the perfect mixture of length and angle. I think using the ramps you were looking at #RR-RACK-4 won't be enough length and too much angle. The ramps you were looking at…

view full answer...

Answer 4

We do indeed offer ramp door extenders in a variety of sizes. For example the Race Ramps Trailer Loading Assist Ramps #RR-TR-5 are a very popular size. These are 67" long ramps and have a 5" lift. They can be used to load a vehicle weighing…

view full answer...

Answer 5

Yes, so long as you have a standard a-frame trailer you will be able to replace your current welded on coupler with the Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Zinc - 2-5/16" Ball - 21K item #DM13205-95. I have attached…

view full answer...

Answer 6

The trick for hanger spacing is to subtract around 3/8 of an inch from the spring length (eye to eye) and then use that dimension for the hanger spacing on a single axle trailer. So for a 23-1/8 inch long leaf spring a spacing of 22-3/4 inches would…

view full answer...

Answer 7

The Race Ramps Wheel Chock for Vehicle Service part #RR-WC-2 will fit on the main platform of the Race Ramps Heavy-Duty XT Ramps for Service and Display - 67" Long part #RR-XT-2-HD although it may hang off just a bit depending on the size of the…

view full answer...

Answer 8

As long as your trailer weighs less than 6,000 lbs the FlatStoppers part #RR-FS-10 that you referenced would work well to prevent your trailer tires from getting flat spots. You would just need to get all 4 wheels of your trailer up onto the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Recommended Ramps for Loading Can Am Slingshot in Toy Hauler Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching