Where is the Stake Pocket Tie-Down Anchors # PK-SPTD Manufactured?

Question

Question:

Where are the PK-SPTD unis manufactured? What country?

asked by: Herb

0

Expert Reply:

The Stake Pocket Tie-Down Anchors # PK-SPTD are is manufactured in China. If you are looking for an option that is manufactured in the U.S., I recommend the Brophy Stake Pocket Tie Down Anchor # TL2B. The ring is a bit larger on the Brophy (3 inches) and you will have the same 4,000-pound maximum weight capacity as the # PK-SPTD.

expert reply by: Bob C

0

Answer 1

You will need a 12 volt battery that is rated for more than 55 amps to power your electric winch. Any battery that meets those requirements should work well for you. For most winches that usually means a car battery. I have included a link to the…

view full answer...

Answer 2

The usable dimensions of the Brophy Stake Pocket Tie Down Anchor part #TL2B are 7-3/8 inches from the center of the pin hole to the plate that sits on top of the anchor, the width is 3-1/2 inches and the depth of it is 1-1/2 inches. This is designed…

view full answer...

Answer 3

Yes, check out the EZ Lock Trailer Coupler Lock #BLTL-20-40D. This coupler lock is compatible with Collar-Lok Couplers and then use for a pin style lock to slide through the coupler you would want the Masterlock Trailer Coupler Lock part #2847DAT.

view full answer...

Answer 4

A trailer that has two 7,000 lb axles has an axle capacity of 14,000 lbs, but trailers aren't always limited by the axles which means a trailer could be rated for 12,000 lbs but have to 7k axles which means it's overall capacity is still…

view full answer...

Answer 5

You should be able to change out the backing plates, hubs, and brakes on your trailer so you can upgrade to higher rated assemblies, but I do recommend checking a couple things on your tow vehicle first. It's possible that your weak braking is…

view full answer...

Answer 6

In order to change from an 7,000 pound axle to an 8,000 pound axle you will need to replace the entire axle with an 8K model. You will not be able to add any parts to your current axle to upgrade it to an 8,000 pound capacity. We do not currently…

view full answer...

Answer 7

It sounds like your current 7-way is attached to the factory hitch of your 2014 Ford F-250 that you will be replacing with the Curt #C14355 and are looking for a way to relocate the 7-way. One solution would be the part #PK12711U that you referenced…

view full answer...

Answer 8

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 9

Yes, it will. The B&W Hitch Receiver Reducer Sleeve item #BWRHXA2182 will work great with your 2022 Ford F-350's 2-1/2" receiver.

view full answer...

Answer 10

So I went out to the warehouse and measured the stake pocket anchor #TL2B and from the lip to the top of the pin hole is right at 6-3/4". As long as your stake pocket is really only 6" deep these will work just fine for you.

view full answer...

Answer 11

The Buyers Products 30 Ton Pintle Hook part #337PH30 is designed for a lunette ring that has a 2-3/8" to 3" inner diameter with 1-3/8" to 1-5/8" diameter section such as the Buyers Products Heavy-Duty Forged 4-Bolt Mount Lunette…

view full answer...

Answer 12

I recommend using the Curt SecureLatch Pintle Hook #CU97FR with the Curt Pintle Hook Mounting Plate #C48349. I really like the SecureLatch because it's a quick and easy way to secure your lunette ring.

view full answer...

Where is the Stake Pocket Tie-Down Anchors # PK-SPTD Manufactured?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching