Replacement RV Step Frame for Dutchmen M-J 23

Question

Question:

Bent door step does not fully retract. Class C RV Dutchmen M-J 23 2001/ E450. Can not determine the step model or manufacturer. Can you advise if your listed steps would be a replacement? Thank you

asked by: Dan O

1

Helpful Expert Reply:

Thanks for the pictures of the steps you have on your Dutchmen, based on seeing them the correct replacement step frame is the part # LC3747457 that you referenced.

expert reply by: Jameson C

1

Step Module
(click to enlarge)

StepLinkage
(click to enlarge)

RV step
(click to enlarge)

Answer 1

I spoke with Lippert and they said the Kwikee Electric RV Step Complete Assembly, 40 Series, #LC3726892 will be a direct replacement for the Coach Steps 725-0043. It will be a bolt-on install for replacement of the steps.

view full answer...

Answer 2

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 5

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 6

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

That is an excellent question and is asked more often than you think. Electric brakes like what come in the Electric Trailer Brake Kit #AKEBRK-2 can be submerged in water when you are loading/unloading your boat. Since water and electricity don't…

view full answer...

Answer 12

Since the discontinued MaxxAir 4700k model fits a standard 14 x 14 RV vent opening, I recommend the MaxxFan Plus Roof Vent w/ 12V Fan - 10 Speed #MA00-04500K. The MaxxFan Plus comes with a thermostat and a remote for easy temperature customization.…

view full answer...

Replacement RV Step Frame for Dutchmen M-J 23

Product Page this Question was Asked From

Continue Researching