Can Bulldog Powered-Drive Kit BD1824200100 Be Mounted On Outside Of Jack To Clear Obstacle?
Question:
I have Bulldog 12k tandem single speed jacks set up on my gooseneck trailer which I want to convert to 12 volt electric jacks. I want to use your Bulldog powered kit for these single speed tandem jacks. However I can only mount the motor on the driver’s side OUTSIDE of the jacks. Your instructions state the motor should be mounted on the inside of the jack legs between the tandem jacks. Can I in fact mount this kit on the outside of the jack on the driver’s side? Thanks for your help.
asked by: Keith T
Expert Reply:
Yes, while it is recommended for the Bulldog Powered Drive Kit # BD1824200100 to be mounted on the inside of your Bulldog 12000lb Jack it can be reversed and mounted on the outside since you have something blocking where the motor would be if you mounted it on the inside of the jack.
I included a video of the # BD1824200100 for you to take a look at.
Products Referenced in This Question
Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Powered-Drive Kit
- Bulldog
more information >
Product Page this Question was Asked From
Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Powered-Drive Kit
- Bulldog
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: 1824200100
- Search Results: venture landing gear
- Q&A: Can Bulldog 12,000lb Trailer Jack Be Adapted To Be Raised/Lowered With Electric Impact?
- Q&A: How to Remove Pin in Handle Shaft to Replace Gears on an Older Bulldog Model 12 Square Jack
- Q&A: Using 1 or 2 Electric Jack Motors for Bulldog Single Speed Jacks with 12,000 Pound Capacity
- Q&A: Will the Bulldog Powered-Drive Kit Work On RAM 12K Jacks
- Q&A: Why Does the Bulldog Powered Drive Kit Part BD1824200100 Include Extra Gears
- Shop: Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity
- Shop: Lippert Polarity Reversing Solenoid by Trombetta for Hydraulic Power Units
- Article: Trailer Wiring Diagrams
- Shop: Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Search Results: 44649
- Q&A: Installation Instructions for Bulldog Powered-Drive Kit # BD1824200100
- Shop: Trailer Hitch
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: Trailer Wiring Harness Recommendation for a 1999 Isuzu NPR
- Shop: Grease Seals 10-36 (pair)
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Article: How to Install E-Track in 3 Easy Steps
- Search Results: trailer jack
- Video: etrailer Electric Jack with Footplate and 7-Way Plug Review
- Shop: Fifth Wheel Hitch
- Shop: Brake Controller
- Video: Review of Dexter Axle Trailer Brakes - Uni Servo Hydraulic Left, Right Brake Assembly - T2351300-200
- Search Results: 68149
- Shop: Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers - Zinc Plated Steel
- Article: How to Accurately Measure Trailer Leaf Springs
- Video: Bulldog Powered-Drive Kit Review
on Accessories and Parts
