Differences Between Hitch Receiver Options For 2011 Toyota Highlander
Question:
2011 Toyota highlander class three hitch Do the Curt and E trailer, and The other brand that fits my 2011 Highlander which I cannot remember the name but it was more of a higher end hitch do they all stick out the back the same?
asked by: Alan F
Expert Reply:
Your 2011 Toyota Highlander is compatible with hitch receivers from Curt, etrailer, and Draw-Tite. These three hitch receivers have a maximum tongue weight of 750 lbs and a maximum gross trailer weight of 5,000 lbs.
The difference from the center of the hitch pin to the edge of the bumper are as follows;
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2", part # e98858, distance = 1 1/2"
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2", part # 13534, distance =1 1/2"
Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2", part # 75726, distance = 0".
The differences between the three hitch receiver options are minimal, though the etrailer hitch receiver is made in the USA and it has a matte black powder coated finish. The other hitch receivers have a glossy black powder coated finish.
I have included product description links and installation videos below.
(click to enlarge)
(click to enlarge)
(click to enlarge)
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- etrailer
more information >
Product Page this Question was Asked From
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Replacement Grease Seal for 2014 Shorelander Boat Trailer
- Q&A: Trailer Grease Seal to Replace 127194TB
- Article: Trailer Maintenance Schedule
- Article: How to Charge a Dump Trailer Battery
- Q&A: Recommended Lithium Battery Compatible Power Converter For Parallax 7355
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Can Brakes Be Added To Mobile Home Axle Used On Utility Trailer
- Q&A: Mobile Home Axle Conversion to Electric Trailer Brakes
- Article: Roadmaster Vehicle Specific Base Plates
- Q&A: 205/75R14 Size Trailer Tire Needed with Load Range D and Speed Rating of at Least 81 mph
- Q&A: Troubleshooting Trailer Tire Wear on the Outside Edge of the Tire
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)