How To Find Correct Replacement Electric Landing Gear Legs for Dutchmen Victory Lane 5th Wheel

Question

Question:

I have a 2004 dutchman 35srv victory lane fifth wheel that the landing gear failed on i would like a replacement but dont know which i need

asked by: Cory

0

Expert Reply:

In order to determine the correct replacement landing gear for a trailer you need the measure the existing legs. The measurement you're looking for is the length of the outer tube and the distance between the weld stops. I see you're looking at electric, if that's what you're after a great option is the Lippert Electric Landing Gear Set part # LC333964. This set uses the standard 15-1/2" weld stop spacing (inside to inside) and 29-1/2" long outer tube.

expert reply by: Conner L

0

Answer 1

The Landing Gear Set w/ Handle part #RVLG-8HDL have a one year warranty and they are designed to replace existing landing gear legs with 15-1/2" between the weld stops (inside to inside). I suspect this is what you have as it's an…

view full answer...

Answer 2

Strangely enough Fulton does not offer replacement landing gear boxes for the landing gear sets. You'd need to look into getting a new set like the Bulldog part #BD500162 which would fit and work well.

view full answer...

Answer 3

The strongest landing gear set that we currently offer is the Ultra-Fab Electric Landing Gear Set #UF17-943010 which is rated for 12,000 lbs. Keep in mind that these are used to support only a portion of your trailer's weight, not the full…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 8

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 9

To determine the best landing gear option for your 1997 Forest River Sierra you'll need to measure the where your weld-stops sit to see if there is a matching set so that you can swap over without having to cut off the old mounting brackets and…

view full answer...

Answer 10

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 11

The MORryde Cushioned 5th Wheel Pin Box #MR84VR weighs right at 190 pounds. Due to this, it will ship freight. Just in case you needed, this is designed to fit 14,000 to 18,000 pound trailers with the Lippert 1621 and 1621HD pin boxes.

view full answer...

Answer 12

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

How To Find Correct Replacement Electric Landing Gear Legs for Dutchmen Victory Lane 5th Wheel

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching