Recommended Replacement Wheel Holders For Platform Bike Rack

Question

Question:

i need to replace all 4 wheel holders on my rack. how do i know which is right one

asked by: Wayne

0

Expert Reply:

Choosing the correct wheel holder will depend on the rack you currently have as each will be specific to the manufacturer and rack. With that being said, the Replacement Universal Wheel Holder for Hollywood Racks Sport Rider E-Bike Rack # HR39FR and # HR59FR will fit the right and left sides of their models # HLY84FR, HR1455Z-E, and HR1450Z-E. If you have one of these models of Sport Rider, these will definitely be the correct replacements for you.

If you do not have one of these racks, these will not be the correct ones. If you can tell me what rack you currently have, I should be able to get you the correct replacement parts.

expert reply by: Lazer S

0

Answer 1

For the Hollywood Rack Sport Rider for E-Bikes #HLY84FR the replacement wheel holder is the part #HR39FR for the right hand side and part #HR59FR for the left hand side. I attached a close up picture of this for you to check out as well.

view full answer...

Answer 2

5,200 lb is a really common axle size so most likely that number is either unrelated to capacity or is what the axle capacity the wheel is normally used with which a wheel like the #274-000011 would easily work as it has a capacity of 3,200 lbs. That…

view full answer...

Answer 3

Only certain bike racks are rated by the manufacturer for use behind RVs or trailers. This is simply because the ride at the rear of an RV is significantly rougher when compared to the rear of a standard passenger vehicle. The reason for this is that…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Recommended Replacement Wheel Holders For Platform Bike Rack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching