Which BAKFlip MX4 Fits My 2021 Honda Ridgeline?

Question

Question:

YOUR SITE SAYS IT WILL FIT A 2021 HONDA RIDGELINE. ARE SIMPLE INSTALL INSTRUCTIONS INCLUDED.

asked by: ARTHUR D

0

Expert Reply:

The BAKFlip MX4 # BAK48602 will fit your 2021 Honda Ridgeline and the installation instructions are pretty simple and straightforward.

expert reply by: Adam E

0

Answer 1

The only difference between the BAK Revolver X2 #BAK39602 and the X4s #BAK78ZR that fits your 2019 Honda Ridgeline is that the X4 has a matte black finish. Aside from the X4 having more of a rugged look there are no other differences between these…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 3

In order to get a ball mount that has effectively 0 inches of rise or drop you would need to get a Trailer Hitch Ball Mount, part #D-4, like the one you referenced that has a 2 inch drop, and then use a 2 Inch High Rise Ball, part #C40034. I attached…

view full answer...

Answer 4

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 12

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Which BAKFlip MX4 Fits My 2021 Honda Ridgeline?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching