Recommended Replacement Tail Light Lens for 8 Inch Long by 3 Inch Wide Trailer Tail Light

Question

Question:

the tail light lens number is SAE AISTP2 04 DOT. What part do I order from E-trailer? 8" x 3"

asked by: GLENN E

0

Expert Reply:

I wasn't able to cross reference the number you provided but I may have a solution for you. The Replacement Tail Light Lens for STL16, STL17,STL18 and STL19 # A16RB would likely be the best replacement option since your lights are 8" x 3".

If you can provide a photo of your existing lights I might be able to confirm this with a bit more certainty.

expert reply by: Erik B

0

Answer 1

The Wesbar Replacement Red Lens, #102641, measures 8 inches wide x 2-7/8 inches tall x 1/2 inch deep. The bolt hole spacing is 7-1/4 inches x 2-3/8 inches (see photo). This lens was designed to fit the Wesbar over 80 Inch Tail Lights #403076 and…

view full answer...

Answer 2

If your tail lights look like #STL16RB or #STL17RB, then you can use the Replacement Tail Light Lens, #A16RB.

view full answer...

Answer 3

The SAE STIAP2 04 DOT number you provided is a DOT approval number, which states that the lens is compliant with DOT regulations. Because of that, that number isn't typically a good identifier for finding a replacement lens. However, in this…

view full answer...

Answer 4

The only way to determine he correct replacement tail light lens is by the model number of the light on your trailer. For example the Replacement Tail Light Lens #A16RB is for Optronics models STL16, STL17,STL18 and STL19. Without that you'll…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 9

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Recommended Replacement Tail Light Lens for 8 Inch Long by 3 Inch Wide Trailer Tail Light

Product Page this Question was Asked From

Continue Researching