SnapPad Compatibility With A 5-1/2" x 5-1/2" Square Jack Foot

Question

Question:

will this fit lippert 5 1/2inch stabilizer feet?

asked by: Matthew N

1

Helpful Expert Reply:

The Replacement Pad for SnapPad Jack Stand Pad System - 5-1/2" Square Jack Foot # SN67FR will fit any brand foot as long as it is square and 5-1/2" x 5-1/2".

expert reply by: Kevin C

1

Answer 1

There are two schools of thought when it comes to determining the correct sized winch for a boat. The first being that the winch should be able to handle 3/4th of the total combined weight of the boat along with the motor, fuel and gear. The second…

view full answer...

Answer 2

The correct replacement circuit board for your MaxxFan 7000k unit is the part #MA10A21275K that you referenced. The different letter in the part number is just a slight change they made but does not affect application.

view full answer...

Answer 3

You shouldn't really have any play with the Easy Grease Trailer Hub and Drum Assembly #AKHD-655-6-EZ-K. If you are getting play in it then the bearings most likely are either not set correctly or were the incorrect choice for your axle's…

view full answer...

Answer 4

Thank you for the photo of your set up, and while we do have an option for a high-quality grill that will allow you to cook outside your RV, there isn't a grill that will fit in the exact mounting arm you have. So the best option we can offer is…

view full answer...

Answer 5

The size winch that you will need depends on a couple of different factors. I have included part of our hand winch FAQ below regarding boat winches and have linked the FAQ article for you to view. Finding the Right Capacity Winch for your Boat…

view full answer...

Answer 6

The Timbren Trailer Suspension Enhancement System for Underslung Axles #T92MR is 5-1/4" tall. Timbren recommends The spring be in constant contact with the frame at all times. So ideally you will want exactly 5-1/4" from your axle tube to…

view full answer...

Answer 7

If you check out the picture I attached for the JT Strong Arm T-Handle Tightening Tool #LC314602 you can see how it can wrap around the T-handle of the Strong Arms. With it in the position that you see you'd use your hand on the other end of the…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

There's unfortunately not a guide to tell us the sizing of your trailer's jack pads so you'll want to measure and note the shape of each pad. I've run into numerous situations where the front and rear pads were either different sizes…

view full answer...

SnapPad Compatibility With A 5-1/2" x 5-1/2" Square Jack Foot

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching