Is There a Heat Sink Needed for Redarc In-Vehicle BCDC Battery Charger part # 331-BCDC1240D

Question

Question:

Is there a heat sink available for the Redarc In-Vehicle BCDC Battery Charger part # 331-BCDC1240D?

asked by: Warren T

0

Expert Reply:

There isn't a heat sink available for the Redarc In-Vehicle BCDC Battery Charger part # 331-BCDC1240D and there isn't really one necessary. It has been tested thoroughly and it does not put off enough heat to require that.

expert reply by: Jameson C

0

Answer 1

If you have an ignition wire running from your 40 Amp BCDC #331-BCDC1240D then the 60-Amp Relay Kit #331-RK1260 isn't needed. There just has to be enough power on that wire to reach back to the BCDC so it can read the alternator properly.…

view full answer...

Answer 2

To connect the 60-amp Relay Kit, part #331-RK1260, to the ignition switch, you can tap into any circuit that receives power when the ignition is on. You may be able to use the fuse for that circuit. For your 2020 Ford F-150, there is a passenger…

view full answer...

Answer 3

If you are looking to connect the 60-Amp Relay Kit for Redarc In-Vehicle BCDC Battery Charger #331-RK1260 to your BCDC 25 amp charging system like the Redarc In-Vehicle BCDC Battery Charger - Dual Input - DC to DC #331-BCDC1225D, you no longer need…

view full answer...

Answer 4

I'd recommend a Pioneer Platform tray like the part #RR42115BF to attach your solar panels to the roof rack #RLZ01-DC via the top channel of the bars. The t-bolts of the tray will allow you to easily connect the platform to the rack and will give…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Thanks for all the details! We definitely have a way to get a cargo basket and an awning installed on your 2024 Toyota Highlander, although the aftermarket roof rack systems will use a clamping system with your door jambs instead of mounting via…

view full answer...

Answer 7

Most if not all trailer wiring harnesses/connectors use larger wires for the 12 volt and ground circuits compared to the other circuits (lights). The sockets themselves don't have an amperage rating so you will go by the draw of the things…

view full answer...

Answer 8

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 9

The Bulldog Winch Ratcheting Wheel Tie-Down Strap #BDW20362 is designed to connect to a D-Ring type of connection point so you wouldn't need to install an e-track on your trailer. For your application I recommend installing the Brophy D-Ring Tie…

view full answer...

Answer 10

Yes we do have backing plates for the e-tracks. I recommend going with etrailer E-Track Backing Plates w/ Hardware - Galvanized Steel - 6" Long x 6" Wide - Qty 4 #e66RR which is a nice kit that includes 4 plates and all the necessary…

view full answer...

Answer 11

Yes, the High Pointe Over the Range RV Microwave #HP74ZR has a two speed exhaust fan which will remove all smoke, steam, and odors out of the immediate cooking area, but it will not vent it outside. If you wanted to have the microwave be able to vent…

view full answer...

Answer 12

The Shocker Hitch Air Cushioned Gooseneck Coupler part #SHK46MR that you referenced can be used with the 4 inch B and W offset ball part #BWGNXA4085 that you mentioned. In fact, the picture we got from Shocker Hitch that I attached to this page shows…

view full answer...

Is There a Heat Sink Needed for Redarc In-Vehicle BCDC Battery Charger part # 331-BCDC1240D

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching