Water Heater Replacement Anode for Hott Rod RV Water Heater

Question

Question:

I converted my RV to accept the Hott Rod electric heating element and I am in search of a replacement anode. They provide one in the kit but these degrade over time And should be replaced. Does Etrailer stock them?

asked by: Scott G

0

Expert Reply:

If you had the 6 gallon Hott Rod conversion kit part # DGR6VP the replacement element would be the part # DGR6P2PB or if you had the 10 gallon version part # DGR10VP you'd need the part # DGR6P10PB.

expert reply by: Jameson C

0

Answer 1

I have attached for you the wiring part of the install instructions for the Camco Propane to Electricity Converter for 6-Gallon RV Water Heaters part #CAM11673 below.

view full answer...

Answer 2

If you know the reference number that was printed on the key, we might be able to obtain a replacement key. If you don't know the key number, you best bet would be to drill the lock cylinder out, or use a cut-off wheel on an angle grinder to cut…

view full answer...

Answer 3

Since the ball mount included with the Gen-Y phantom has a hollow shank I recommend using the #63232 which threads into the ball mount. Due to the design of this receiver a more traditional clamp style option like #e99007 isn't going to work…

view full answer...

Answer 4

The wattage of the anode rod and the length are different between the 10 gallon Hott Rod Conversion kit part #DGR10VP and the 6 gallon one part #DGR6VP. The 10 gallon setup has the longer rod which is 675 watts and the 6 gallon has the shorter rod…

view full answer...

Answer 5

The ground pin of a trailer side 7-way connector like the 7-Way Molded Trailer Wire Connector, 4' Long #H20043 you were looking at is the 5 o'clock position as shown in the included picture. For the vehicle side of the 7-way connector it…

view full answer...

Answer 6

Best option would be to cut off your damaged 7-way and wiring and then splice in a new one like with the part #H20043 which comes with a 4 foot lead of wire.

view full answer...

Answer 7

The cable for the Hott Rod RV Water Heater Conversion Kit #DGR6VP is removable from the Heating Element #DGR6P2PB. You will simply pull the end of the cable off the heating element when you need to remove it for draining your water heater.

view full answer...

Answer 8

When turning your Atwood/Dometic G6A-8E water heater from propane to electric you will need The Hott Rod RV Water Heater Conversion Kit #DGR6VP. This conversion kit converts your RV's propane water heater to electric operation, while keeping your…

view full answer...

Answer 9

Short answer, yes you can convert from 30amp to 50 amp. It will be costly and require an electrician. Long answer, you will need to replace the power outlet with SmartPlug RV and Marine Power Inlet - 50 Amp - Stainless Steel #SM79FR. Then replace the…

view full answer...

Answer 10

Hello Scott. The Heating Element #DGR6P2PB is designed to replace the element included with the Hott Rod RV Water Heater Conversion Kit #DGR6VP. We do offer a replacement anode rod for the suburban 6 gallon water heaters, part #CAM11563, but I am…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Water Heater Replacement Anode for Hott Rod RV Water Heater

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching