2009 Ford F-350 Super Duty Third Brake Light Camera Compatibility

Question

Question:

My factory tail gate camera monitor 6.5 inchs. Cant find any specs. on that Camera system.

asked by: David

0

Expert Reply:

In order for the Custom Third Brake Light Camera for Aftermarket Monitor - Night Vision, part # 3460007, to work with your 2009 Ford F-350 Super Duty setup you will need to install a switcher for the camera. This camera has 420p resolution, 316224 pixels, and a 170° view angle.

I have included a product description link and a video link below.

expert reply by: Mark Smith

0

Answer 1

The Custom Third Brake Light Camera for Aftermarket Monitor #3460007 you referenced has a power and ground wire setup (black and red bonded wire with black connectors) and has a video signal circuit that is carried on the yellow RCA cable. For more…

view full answer...

Answer 2

The u shaped wire on the Custom Third Brake Light Camera for Aftermarket Monitor #3460007 is used to adjust the camera.

view full answer...

Answer 3

Here's a screenshot of the installation instructions. In summary, you'll remove the existing 3rd brake lamp, and install the new one after feeding the wiring harness into the opening on the rear of the cab above the rear window. Make sure the…

view full answer...

Answer 4

Usually that is the case, however the Custom Third Brake Light Camera for Aftermarket Monitor #3460007 is designed to be installed into the factory screen in your 2016 Ford F-350 via RCA connectors, and in turn would only send power to the camera…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

2009 Ford F-350 Super Duty Third Brake Light Camera Compatibility

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching