Can a Lippert Axle be Replaced with a Dexter Axle?

Question

Question:

Hi I’m looking for a replacement axle beam only Mine is a lippert brand 93” hub face 79” spring center 6000lb Straight no spindles Wasn’t sure if you have one in stock or if dexter is interchangeable Thanks adam

asked by: Adam

0

Expert Reply:

We do have a straight Dexter axle that is very close to your Lippert one. The # 7461121 will be 95 inches from hub face to hub face and 80 inches from center of one spring seat to the center of the other. The branding of the axle typically doesn't make a difference as long as the measurements match or are very very close.

expert reply by: Lazer S

0

Answer 1

I would recommend Dexter Torflex axles the highest for torsion axles. And then put Al Ko and Lippert at about the same in quality. I was searching around online and the common consensus among the trailering forums is that the Dexter axles are…

view full answer...

Answer 2

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 3

You have a Lippert 3500 lb axle with 10 inch brake assemblies/hub drums. We can't order custom axles, but we do offer a Dexter #7359765-EB off-the-shelf axle that's very similar, the only difference is that the leaf spring seat center…

view full answer...

Answer 4

To replace your Lippert axle, we have the Trailer Axle w/ Electric Brakes - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 89" - 3,500 lbs #e43SR or the Dexter Trailer Axle w/ Idler Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs…

view full answer...

Answer 5

I am not sure what you mean by MTI number?

view full answer...

Answer 6

The Dexter hub you referenced, 8-201, is a 5,200 lb hub, though a 5 on 4-1/2 bolt pattern does not come on 5,200 lb hubs. The correct bearings for the 5,200 lb hub are #25580 and #LM67048, while the proper races are #25520 and #LM67010. I have…

view full answer...

Answer 7

The MTI number on your 8-201 hubs is simply a casting number. It does not indicate any information about the hubs or have anything to do with the actual part number. I'm not surprised to hear you have different outer bearings between the two…

view full answer...

Answer 8

Since you have a 3,500 lb axle most likely the diameter of the threaded portion of the spindle is 1 inch. You will need to verify that. And since the spindle has a hole in it for a cotter pin you would need a castle nut. For that I would recommend…

view full answer...

Answer 9

To add grease to the Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles #84546UC3-EZ I recommend using the LubriMatic Prime Guard High Temperature Wheel Bearing Grease #L11380. This is the same type of grease used in our pre-greased…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Can a Lippert Axle be Replaced with a Dexter Axle?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching