Using SnapPad Jack Pads On An Andersen Block

Question

Question:

can the rv snap pads be attached to the bottom of a andersen block?

asked by: Randy C

0

Expert Reply:

As long as your Andersen Blocks are 9" in diameter and have a lip of around 1/8" you should be fine using the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 9" Round Jack Feet - Qty 4 Item # SP54FR4. If you have issues keeping them attached SnapPad also recommends using 1/4" thick bolts with nylon nuts to bolt the SnapPads to jack feet so you could do the same with the blocks.

expert reply by: Kevin C

0

Answer 1

To know what pin box will replace your MORryde pin box you'll first need to identify the bolt pattern. To do this you can follow the steps in the attached pin box identification article. This article will show you the different styles of…

view full answer...

Answer 2

I was unable to identify your exact axle but I found Trailer Hub and Drum Assembly #AKHD-865-7-2-EZ-K to work if you have EZ Lube axles. If you do not have EZ Lube axles use Trailer Hub and Drum Assembly #AKHD-865-7-2-K. Both of these kits will come…

view full answer...

Answer 3

I've had the installation instructions for the Replacement Entry Door Hinge for RV - 6 Leaf - White Item #LC198295 added to the item page for you and they'll also be attached to this answer page if you scroll down.

view full answer...

Answer 4

That is correct. The #GS-2250DL is the direct replacement for your old grease seal marked P02860 on your 2019 Keystone Cougar.

view full answer...

Answer 5

For the Reese Sidewinder #RP34FR during the initial installation you can apply white lithium grease to the inner tube of the turret to ease installation. White lithium grease will need to be applied to the wear plate (between the turret and the arm)…

view full answer...

Answer 6

If your 2019 Chevy Silverado 2500 HD Duramax already has a built in TPMS, I don't think you'd need to add the additional sensors to the TST TPMS for RVs - Color Display - Signal Booster - 4 Flow Through Tire Sensors #TST-507-FT-4-C, but I…

view full answer...

Answer 7

Because it's lighter, less expensive, has fewer moving parts and is mechanically less complicated I'd recommend going with the Gen-Y #325-GH-8040 shock absorbing pin box versus a Trailair Flex Air like part #LC328492. The Trailair features a…

view full answer...

Answer 8

Yes. The MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert 1621HD #MR84VR can be used to replace a Lippert 1621 or 1621HD; this pin box replacement is designed for trailers with GVWR up to 18,000-lbs so it is rated properly for…

view full answer...

Answer 9

The proper size Lube plate for use with the B and W Companion hitch is a 10 inch diameter lube plate. We carry two lube plates this size. The Reese Lube Plate for Reese 5th Wheel Trailer Hitches - 10 inch Diameter, item #RP83002, and the Curt 10 inch…

view full answer...

Answer 10

The Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box - Lippert 1621 and 1621 HD - 18,000 lbs - 3.5K TW #325-GH-8040 weighs 125-lbs. However, after speaking with the tech and warranty department over at Lippert, the Gen-Y pin boxes are not…

view full answer...

Answer 11

We do have air bags available that are compatible with an in-bed hitch and also a fit for your 2022 Chevrolet Silverado 2500. I recommend the Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle #F2613. These air helper springs have…

view full answer...

Answer 12

MORryde #MR64VR, #MR74VR, #MR84VR all have a GTW of 18,000lbs but each have a finetuned spring capacity for a smoother ride which is why you see 11.5k listed for the #MR64VR. Since your 2018 Grand Design Reflection 303 has a GVWR of 11995 and…

view full answer...

Using SnapPad Jack Pads On An Andersen Block

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching