Slide Out Topper for 153 Inch Wide RV Slide-Out

Question

Question:

My slide out measures 153 inches from outside edge to edge, what size topper should I get. I would like a black one.

asked by: Nicholas W

0

Expert Reply:

If the flange-to-flange width of your slide out (widest point of slide-out) measures 153 inches, I'd recommend the Solara # LCV000168109 slide out topper, in black which is what Solara recommends for slide-outs measuring between 152-157 inches wide. The kit includes the awning, awning rail, brackets and all necessary hardware.

If you click the provided link, you can see a video of my buddy Shane pointing out the features of the slide topper.

expert reply by: Mike L

0

Answer 1

For your 81 inch flange to flange slide out, the Solera 7.5' Slider (Slide-Topper) in White w/ White Hardware, #LCV000163287 or the #LCV000165062 in black with black hardware are the correct size for your 5th Wheel. This will fit slide out boxes…

view full answer...

Answer 2

Measuring to pick out the correct slide topper for an RV like your 2018 Forest River Rockwood is pretty easy. You have to measure the box width including the flange on it and you'll be set. So the Solera part #LCV000163288 that you referenced is…

view full answer...

Answer 3

The correct Solera RV Slide-Out Awning for a 153.5" slide-out is part #LCV000163300 for white or part #LCV000168109 for black. The correct Solera RV Slide-Out Awning for a 83.5" slide-out is part #LCV000163287 for white or part…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...