How Long is the Cable of the Rear View Safety Backup Camera System # RVS-770718

Question

Question:

how long is cable for Item # RVS-770718?

asked by: E H

0

Expert Reply:

The cable of the Rear View Safety Backup Camera System # RVS-770718 is 66 feet long.

expert reply by: Jameson C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Hi Mark; thanks for the question and I have some good news for you as we have the exact 5th wheel to gooseneck adapter to replace the Turning Point pin box on your Jayco Eagle HT 30.5 CKTS. The correct part is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

There might be a solution but it all comes down to what gooseneck hitch you have installed in your truck. If you can let me know what brand hitch you have I can help find you exactly what type of slider hitch solution would work best. Hopefully you…

view full answer...

Answer 6

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 7

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 8

Hey Jim, congrats on the new truck and fifth wheel - looks great. Our rule of thumb is that you want a minimum of 6" of clearance between the top of the bed rails and the bottom of the trailer loft. You should be just fine to use the bottom hole…

view full answer...

Answer 9

Thanks for the pictures! To replace your Curt Turning Point you will want the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item #GY48GR. This was made specifically to replace the Turning Point pin boxes. You will also need the Safety…

view full answer...

Answer 10

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In regards to a Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter like part #RP94720 and a Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Adapter Pin Box like part #325-GH-8045, the main difference is that one uses air for…

view full answer...