Entry Height Requirements For A Lippert SolidStep Manual Fold-Down Step

Question

Question:

My entry height is 18”, can I still use these steps even though it says a minimum entry of 22”, thinking that the first step will just be short and extend the legs less?

asked by: MICHAEL D

0

Expert Reply:

I spoke with Lippert, the manufacturer, and their tech stated that the SolidStep Manual Fold-Down Steps for 29" to 36" Wide RV Door Frames - Double - Aluminum Item # LC733932 legs will slide up and easily allow for your 18" entry height.

expert reply by: Kevin C

0

Answer 1

The manufacturer for the SolidStep Manual Fold-Down Steps for 29" to 36" Wide RV Door Frames - Double - Aluminum Item #LC733932 says the lowest setting for the legs is 3-4" so you should be able to be at that 20" entry height and…

view full answer...

Answer 2

The widest point of the Lippert #LC733932 Solid Step is 24 inches, which is the dimension from the outside of one stringer to the outside of the other. The latching mechanism that holds the steps folded upright into their storage position is width…

view full answer...

Answer 3

I have attached a few photos for you with all the dimensions we have for the Ark Drop Down Corner RV Stabilizer Jacks part #AR34FR. That said, Ark is an Australian company so the measurements are in metric, millimeter to be specific so you may need…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Hey Beatrice, To find the right fit for your trailer's suspension you'll need to take a quick measurement of your current shackle straps. You'll need to measure from the center of one bolt hole to the center of the other bolt hole. The…

view full answer...

Answer 11

Hey Dave, the MORryde upgraded shackle kit part #MR76ZR that you referenced is compatible with your 2020 Grand Design 2670MK and the Lippert Road Armor equalizers.

view full answer...

Answer 12

The SolidStep Manual Fold-Down Steps are a great choice for your Jayco 5th Wheel Camper. The amount of steps needed depends on your entry way height from the ground. The SolidStep Manual Fold-Down Steps for 26" to 29-7/8" RV Door Frames…

view full answer...

Entry Height Requirements For A Lippert SolidStep Manual Fold-Down Step

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching