Replacement RV Entry Door Locking Latch Kit

Question

Question:

I am looking for a replacement door latch lock for my trailer. The lock that is currently installed is a Fastec Leo Lock. The Leo locks cut out is 3.66inch wide 4.409inch high. I need a replacement lock. I can widen the hole if needed. What do you recommend?

asked by: Cody H

0

Expert Reply:

Please take a look at the Bauer Products Motorhome Door Lock, # BA64FR. This installs into latch cutouts that are 5-1/4" wide x 4-1/2" tall.

Please note the attached product review and installation videos.

expert reply by: Michael R

0

Answer 1

Lippert Components Slam Latch Baggage Door Handle was the Southco that has been discontinued. I recommend upgrading your locking handles to the Global Link RV Baggage Door Slam Latch with Keyed Alike Option - Black - 1-3/4" Thick…

view full answer...

Answer 2

I spoke with the manufacturer and the Bauer Products Motorhome Door Lock - Black #BA64FR strike plate mounting holes has a 5-1/2" measurement from center to center.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

We may have some potential options for replacing the tack room door lock on your Featherlight trailer. Is the 5" L x 5" H dimension you gave for the door cutout or the lock itself? The best way to find the right replacement lock is…

view full answer...

Answer 5

I contacted Trimark in regards to a replacement part for the Trimark 030-0900. 030-0900 is actually a series number not a specific part number. To find the part number you will need to take the interior handle completely off the unit. On the back…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Jimmy, The Global Link Locking Baggage Lock Actuator Set with Mounting Plate #GL34FR you referenced requires a cutout hole measuring approximately 3.75" x 3.75" and a door thickness of 0.7" to 1.25" thick. You can unscrew the…

view full answer...

Answer 8

RV manufacturers will typically just turn the handle 180 degrees for other orientation and the deadbolt will just be on the opposite side of the plunger. If your deadbolt sits above the plunger on yours and the cutout hole is 2-1/2" to 3"…

view full answer...

Answer 9

Hello John. The #C96JR tail light kit for the 2023 Jeep Gladiator will indeed work with a Brake Buddy brake System Such as part #HM39524. So, if you plan to use a portable brake system, that is definitely what I recommend, and you do not need to get…

view full answer...

Answer 10

I have some great replacement RV door latch options. The only one we offer that would come close to fitting such a large cutout is the Bauer Products Camper Door Lock part #BA65FR which fits up to 5-1/4" wide x 4-1/2" tall openings so…

view full answer...

Answer 11

Our Bauer door lock part #BA64FR is the same as the BP-12 that you mentioned so this will work great.

view full answer...

Answer 12

For your 2024 Ford F-53, I recommend checking out the Timbren Front Suspension Enhancement System #TFFF53B for the front, and the Timbren Rear Suspension Enhancement System #TFRF53A for the rear. These kits do not require drilling, will replace your…

view full answer...

Replacement RV Entry Door Locking Latch Kit

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching