Demco Hijacker Above-Bed Base Rails 2016 Toyota Tundra

Question

Question:

Just want to make sure that these will work for a 2016 Toyota Tundra with 6.5’ box

asked by: Jay F

0

Expert Reply:

Yes, the Demco Hijacker Premier Series Above-Bed Base Rails and Semi-Custom Install Kit for 5th Wheel Hitches, # DM8552020-71 is a confirmed fit for the 2016 Toyota Tundra with 5-1/2, 6-1/2, or 8 foot bed.

expert reply by: Michael R

0

Answer 1

For your 2017 Toyota Tundra short bed we have the Demco fifth wheel rail kit part #DM8552020-71 as a confirmed fit that would work great as long as your Pullright hitch is one of the ISR style of hitches designed to fit above bed rails. This rail kit…

view full answer...

Answer 2

The best 5th wheel hitch combination for your 2016 Toyota Tundra CrewMax is going to be the Demco Premier Series Above-Bed Base Rails item #DM8552020-71, the Demco Autoslide 5th Wheel Trailer Hitch item #DM8550040, and the Curt Above-Bed Gooseneck…

view full answer...

Answer 3

For just the brackets of the #DM8552020-71 you would just need the part #DM8552020. This will be just the bracket and hardware of the rail kit you referenced.

view full answer...

Answer 4

Since your truck bed is shorter than 6 feet in length a standard slider hitch still wouldn't give you enough turning clearance but we do have one option that would give you enough clearance as it slides back 22-1/2 inches instead of the normal…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Demco Hijacker Above-Bed Base Rails 2016 Toyota Tundra

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching