Die-Cast Grate for Furrion 2-in-1 Range Oven

Question

Question:

We are looking to upgrade the grate for Furrion FSRE17SASS. This appears to have proper dimensions. Please advise.

asked by: Terry H

0

Expert Reply:

Yes, you can upgrade the grate on your Furrion 2-in-1 range oven with the die-cast option from Furrion:

- Die-Cast Grate for Furrion Range Cooktop # CFSRE21SA002

I have added a link below to a video review for you to check out as well if you'd like to take a look.

expert reply by: Kyle S

0

Answer 1

We don't know for sure if the #CFSRE21SA002 will fit on your Amana RV stove since they're not designed for the same product, but I can tell you that the grates are 19" long (wide) and will sit 1-3/8" tall. The front grate is…

view full answer...

Answer 2

Since we have confirmed with Furrion that the replacement top part #C-FSRE21SA-SS-003 fits your FGHWCLDA-SS that means that you could use the grate part #CFSRE21SA002 as well to upgrade what you have.

view full answer...

Answer 3

The replacement grate you are looking for is the part #CFSRE21SA002 for your Furrion oven F1S21L02A that you referenced.

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 6

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Die-Cast Grate for Furrion 2-in-1 Range Oven

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching