Availability Of Wiring Instructions For Repeater Dock For Tire Linc TPMS For RVs LC37VR

Question

Question:

Does this come with wiring instruction if rv has no repeater dock?

asked by: Daniel B

0

Expert Reply:

There sure is!

Since your trailer does not have a repeater dock you will need to install the repeater dock included with the Tire Linc TPMS for RVs and Trailers w/ Signal Booster # LC37VR and wire it to the battery of your RV. You will need to install a 15 amp fuse inline of the power wire on the repeater using an inline fuse holder like the # SWC9544.

The # SWC9544 uses mini fuses like what is found in the Mini Fuse Kit # PT62FR.

I included a videos for each of the products mentioned, and you can find the wiring details on the 3rd page of the included written instructions.

expert reply by: Samuel C

0

Answer 1

For your 2011 Chevy Silverado I recommend starting with the RoadActive Suspension Kit #RAS4611 that you mentioned by itself to see how everything handles when pulling your 34 foot trailer. It wouldn't necessarily be…

view full answer...

Answer 2

Using these two products together is going to be a little bit of overkill, but I spoke with RoadActive Suspension and they mentioned that as long as your current bump stop (which would be replaced by a Timbren system) sits inboard towards the…

view full answer...

Answer 3

We have not had any issues with our customers and the TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster #TM56FR draining trailer batteries but a great idea is to run a length of 10 gauge wire like part #10-1-1 from the 12 volt accessory…

view full answer...

Answer 4

The round or trunnion bars refers to the end of the spring bars. Round bars are typically designed for lighter applications, are a bit harder to install and are usually priced lower than trunnion bars. Trunnion bars are typically designed to be…

view full answer...

Answer 5

You'd be fine to have a weight distribution installed on your trailer as you travel on the hill you described. If anything it might help prevent the trailer from leaning excessively. For a 6,000 lb trailer you'd be looking at a tongue…

view full answer...

Answer 6

My contact at Lippert was able to give me some information regarding the Tire Linc TPMS #LC37VR. The size of the sensor is fairly small, measuring about 3/4" thick and weighing 11 grams each. The battery life will depend on how much the…

view full answer...

Answer 7

The correct locking 5th wheel hitch pin that will replace your factory 5th wheel hitch pin is the Tow Ready Base Rail Lock for 5th Wheel Trailer Hitches part #TR63254. The locking hitch pin has a 1/2" diameter which is the same as the…

view full answer...

Answer 8

As an example, tire and wheel combination #LHAW121 uses a 5" wide wheel and 205/75-15 tire, which is 8.1" wide. If the Timbren Timbren Axle-Less Trailer Suspension System #A20RS545 has 4-7/8" of space between the frame and…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 12

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...