How to Remove Crank Handle on Sidewind DL-3400 Jack

Question

Question:

How do you remove the broken handle on DL 3400 1200 lb. sidewind jack handle?

asked by: Steven J

0

Expert Reply:

We actually put together a short video on repairing a similar jack that will show you how to access and remove the old crank and replace it with the # MJ-1500B-HD. Your DL-3400 should have a screw at the top that is holding the end cap on; you'll want to remove that screw and then look for the pin holding the handle to the upper gear- the video does a good job of illustrating this around the 4:50 mark.

expert reply by: Erik B

0

Answer 1

The CC316-01 number you referred to is the original part number of the fan motor. Is it a replacement fan blade or motor you're needing? If that's the case, you'd use the #BVD0218-00-R replacement motor. If you were needing a…

view full answer...

Answer 2

There really is no elegant way to do it. The knob is held in place by a pal nut, which must be removed. It might be possible to get a screwdriver in next to the nut and pry it off, or grasp the end with pliers and rock it back and forth until it can…

view full answer...

Answer 3

We do have a couple of alterative solutions, however we do not carry a replacement that match those dimensions. Instead, I recommend replacing the entire swing down stabilizer with the Stabilizer Jacks #TJ01RT-HD which measures 18" extended,…

view full answer...

Answer 4

To repair a Ram Series 12000 jack, like #TJD-12000SP-R2, we have the Gear Kit #TJD-12000-GR or the Replacement Rod and Nut #TJD-12000-RODNUT. Or you could need both. I just depends on what the problem is exactly.

view full answer...

Answer 5

I went out to the warehouse and measured Replacement Cap #MJ-1500B-CP for you. The threaded part has a diameter of 2.08 inches. The overall diameter is 2.19 inches. I have included a picture showing these measurements.

view full answer...

Answer 6

We do offer replacement parts for Fulton jacks, including the square tube type. These parts are not always a universal fit, so you will need to order replacement parts that are rated correctly for your particular Fulton jack. Your jack model number…

view full answer...

Answer 7

The Aquashed and the Olefin RV covers both do great in winter applications like yours. Adco has told us that the two lines you mentioned are the best for that type of climate, but overall, I'd give edge to the Olefin like the part #AD47ZR that…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How to Remove Crank Handle on Sidewind DL-3400 Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching