Similar Rod/Paddle Carrier to ER37VR that Attaches to Roof Rack Top Channels

Question

Question:

Do you have T-Slot bolts and nuts that could be used to channel mount this part? Thanks.

asked by: Dave M

0

Expert Reply:

While we don't have a T-slot adapter for the # ER37VR that you referenced to attach it to the top channel of a roof rack we do have the Rhino Rack multipurpose holder part # RRRMPHU which is a very similar style of carrier that was designed to attach to the top channel of a crossbar like you are looking for.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

We do offer a direct replacement for the Dometic Duo-Therm RV Air Conditioner. The Advent Air RV Air Conditioner part #ACM135 for 13.5K or part #ACM150 for 15K is what I recommend. This unit will be a plug and play fit and it will work with your…

view full answer...

Similar Rod/Paddle Carrier to ER37VR that Attaches to Roof Rack Top Channels

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching