Firestone Pressure Switch that Shuts off Compressor at 120 PSI

Question

Question:

Cant find off @ 120 psi switch for my stystem.

asked by: Doug H

0

Expert Reply:

We do have a Firestone pressure switch for the Remote Air Command kits that comes on at 90 psi and shuts off at 120 with the part # F9401.

expert reply by: Jameson C

0

Answer 1

The Replacement Control Unit for Kwikee Electric RV Steps #LC379146 which is part 90950600 you referenced is does not have a specific wiring diagram, but I've attached the closest thing and have also included a video of an installation to…

view full answer...

Answer 2

It sounds like you have a couple wires run backwards on your Lippert powered steps. Its hard to say exactly which wires are wrong but most likely a power wire and ground is backwards. The best recommendation I can give would be for you to go over the…

view full answer...

Answer 3

Thank you for that info and we do have the exact replacement for your Kwikee 33 Series step 903300906. What you will need is the following: - Replacement Step, Motor, and Switch for Kwikee RV Electric Steps - 33 Series #LC3722662 The is the exact…

view full answer...

Answer 4

The Replacement Control Module for Lippert Electric Coach Step #LC301702 is the correct fit for your Lippert Coach step. The long green wire with the ring terminal is your ground and will be attached bare metal to metal on our coach frame. The short…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Firestone Pressure Switch that Shuts off Compressor at 120 PSI

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching