Do the Arms for the JT's Strong Arm Jack Stabilizer Kit Go In Front or Behind Jacks

Question

Question:

I have a few questions about the installation of the strong arm system. First do the cross bars ha e to be in the front or can the be on the back of the jack on the front of the trailer. Second same for the rear Jacks.

asked by: Jonathon N

0

Expert Reply:

In regards to the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers part # LC191025, the arms have to be installed in front of the front jack and behind the rear jacks per the instructions. The full copy of the installation instructions are attached below as well.

expert reply by: Conner L

0

Answer 1

Trailer manufacturers list the loaded tongue weight for a trailer as being 10% of the loaded weight of the trailer, which is why you see 1,050 lbs for a GVWR of 10,500 lbs for your trailer. In reality you can make the tongue weight whatever you want…

view full answer...

Answer 2

Thank you for your purchase from etrailer of the JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs w/ 58" or More Between Landing Gear #LC191023. The orientation does not need to be chanced it is just rearranging the bars like you…

view full answer...

Answer 3

Yes, we do have weight distribution system options which come equipped with a solid, one-piece 2-1/2" shank. There are not many options but of them, I recommend the Equal-i-zer Weight Distribution System part #EQ64FR which is for trailers from…

view full answer...

Answer 4

Can you send me a picture of the feet of your jacks? How far apart are they?

view full answer...

Answer 5

You can get the breakers at any home center or electrical supply house. They are an off-the-shelf item and aren't specific for this purpose. According to Progressive Dynamics, the following breakers are suitable replacements: -ITE/Siemens—QP,QT…

view full answer...

Answer 6

view full answer...

Answer 7

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 8

So I have your hub narrowed down to a few different possibilities but we need to know what your bolt pattern is to know for sure. We have the part #84556UC3 for if your bolt pattern is 5 on 5 inch. We have the part #845476UC3 for if your bolt pattern…

view full answer...

Answer 9

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Do the Arms for the JT's Strong Arm Jack Stabilizer Kit Go In Front or Behind Jacks

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching