Compatible Hitch Fit for Ranch Hand Legend Aftermarket Bumper on 2009 Chevy Silverado 2500
Question:
Recommended Trailer Hitch Receiver For 2009 Chevy 2500HD With Ranch Hand Legend Bumper. Looking for something that would bolt to frame as well as to bottom of this bumper like the oem one would at least there instruction show it bolting to a frame mount hitch using spacer plates 1/4 - 3/8 thick. Trying to take advantage of the stoutness of bumper. It would have to have a pretty significant projection to the rear to clear bottom plate of bumper center. Thanks. I shop with you folks due to your quality service and knowledge.
asked by: Eric
Expert Reply:
The hitches we offer for your vehicle are designed for use with the factory bumper, but we do have options that might work for you.
The deepest drop custom hitch we offer for that truck is the B&W # BWHDRH25187 which has a 6-1/2 inch drop. The drop is the vertical distance between the underside of the frame member and the underside of the bumper. If this distance on your truck is less than 6-1/2 inches, then the # BWHDRH25187 would be a fit.
If that amount of drop isn't sufficient, you could go with a Universal fit Class V universal weld-on hitch like the Curt # C37CR for a 9 inch drop or the # C59CR for an 18 inch drop.
Products Referenced in This Question
B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 1600 lbs TW
- 16000 lbs GTW
- 16000 lbs WD GTW
- 2 Inch Hitch
- 1600 lbs WD TW
- Visible Cross Tube
- B and W
more information >
Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 44" Wide
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 44 Inch Wide
- 2000 lbs TW
- 20000 lbs GTW
- Class V
- 2-1/2 Inch Hitch
- 9 Inch Drop
- CURT
more information >
Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 62" Wide
- Heavy Duty Receiver Hitch
- Weld-On
- 18 - 62 Inch Wide
- 2000 lbs TW
- 20000 lbs GTW
- Class V
- 2-1/2 Inch Hitch
- 18 Inch Drop
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 1000 lbs TW
- 10000 lbs GTW
- 12000 lbs WD GTW
- 2 Inch Hitch
- 1200 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Front Mount Hitch
- Shop: Gooseneck Hitch
- Shop: B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Front Runner Slimline II Platform Rack - Ditch Mount - Low Profile - 61-7/16" x 56-1/8"
- Shop: Powerbuilt Triple Lift Jack w/ Locking Safety Bar - 17-1/2" Lift - 4,000 lbs
- Shop: Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Roof Rack
- Shop: Grille
- Shop: Base Plate for Tow Bar
- Shop: Floor Mats
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Video: Trailer Hitch Installation - 2002 Chevrolet Silverado - Curt
- Video: Best 2002 Chevrolet Silverado Hitch Options
- Q&A: Trailer Hitch for 2003 GMC Sierra 2500HD with Additional Drop
- Q&A: Recommended Trailer Hitch for a 2006 Chevy Silevrado 3500 with Service Body
- Q&A: Class V 2-Inch Hitch Fits for 2003 GMC Sierra 3500 4x4 Dually
- Search Results: 530x12
- Search Results: curt ball mount only
- Video: Review of Equal-i-zer Inner Link Plate for 8 Inch Trailer Frames - EQ90-02-5208
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Can An Aftermarket Trailer Hitch Be Installed On a 2007 Toyota Tundra If Bumper Is Replaced
- Q&A: Will The Rock Tamers Mud Flap System Fit On A Shocker Hitch HD Ball Mount
- Search Results: gen y torsion
- Video: Trailer Hitch Installation - 2014 Dodge Ram 2500 - Curt
- Q&A: Can a Weight Distribution System be Used on an I Beam Trailer
- Q&A: Weight Distribution System For Hauling a Dump Trailer
- Video: Roadmaster Anti-Rattle Hitch Extender Review