Is Mounting Bracket of Extreme Off-Road Ratcheting Trailer Jack w/ Dual Wheels # ARK54FR Steel

Question

Question:

Is the mounting base made of steel and can it be welded to the frame rather than u-bolted? Is there a smaller mounting base available without the holes for a welded option?

asked by: Jon M

1

Helpful Expert Reply:

The mounting plate of the Extreme Off-Road Ratcheting Trailer Jack w/ Dual Wheels # ARK54FR is steel so you could weld it to your trailer frame. There isn't a version of this though that has a smaller mounting base/bracket.

expert reply by: Jameson C

1

Answer 1

The Extreme Off-Road Ratcheting Trailer Jack part #ORJW1SU has a 770 lb weight capacity which means so long as the tongue weight of the trailer does not exceed this then you'd be fine. A trailer with GVWR of 4,000 lbs would be no worry at all.

view full answer...

Answer 2

The ARK #ORJW1SU Off-Road trailer jack will need about 21-3/4 inches of available space on the trailer tongue. I wasn't able to make out the dimensions on your tape measure in the photo, so I couldn't say judging by that if it'll fit.…

view full answer...

Answer 3

I spoke with Ark and they told me that the Extreme Off-Road Ratcheting Trailer Jack w/ Dual Wheels #ARK54FR stick out 9-1/2 inches from the trailer frame it attaches to.

view full answer...

Answer 4

The Titan Zinc-Plated, Leverlock Coupler #T4845000 measures 4-1/8 inches tall, so it looks like it may be too tall for your set up. If so, the only other 5,000 lb coupler for a 2" hitch ball that may work is one that has half of the height, the…

view full answer...

Answer 5

The Xtreme Off-Road Ratcheting Trailer Jack w/ Dual Wheels #ARK54FR will hold in place when pushing up the slope. If you're going down the slope the mechanism will not hold it is place, as the wheel is designed to free spin in the direction of…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Is Mounting Bracket of Extreme Off-Road Ratcheting Trailer Jack w/ Dual Wheels # ARK54FR Steel

Product Page this Question was Asked From

Continue Researching