What Is The Slotted Section In Bracket For Wheel Masters Level Master Trailer Bubble Level Used For?

Question

Question:

What is the purpose of the slotted section for mounting this WM6780 RV leveler bracket? It seems that if you level your 5th wheel prior to installation, you would use the single holes to mount it stationary, avoiding having to re-level your camper if the leveler gets bumped and moves in the slotted section. The instructions are not specific, but the diagram looks like the slotted section is used for the rear mounts. Your video shows that all single stationary holes were used. Am I missing something?

asked by: Richard B

0

Expert Reply:

You are correct, the slotted section of the bracket on the Wheel Masters Level Master Trailer Bubble Level with 5th Wheel Pin Box Mounting Bracket # WM6780 is another option for mounting the level to your pin box.

I do not recommend using the slotted section as the only rear mount since as you mentioned it can cause the level to move if it is bumped, but instead I recommend using the two stationary holes as shown in the included video.

expert reply by: Samuel C

0

Answer 1

The mounting brackets for the Wheel Masters Level Master Trailer Bubble Level with 5th Wheel Pin Box Mounting Bracket #WM6780 are made out of UV-protected plastic. The plastic is really durable though, and is designed to last, so it isn't going…

view full answer...

Answer 2

I do have an option for you but the Camco AccuLevel Trailer Bubble Level part #CAM25563 does not come with brackets or hardware to install. I recommend Wheel Masters Level Master Trailer Bubble Level with 5th Wheel Pin Box Mounting Bracket part…

view full answer...

Answer 3

I am sure you could use adhesive to attach the Wheel Masters Level Master 2 Trailer Bubble Level #WM67200 to your fifth wheel if you wanted to but we don't have an option for that. You could use something like Liquid Nails.

view full answer...

Answer 4

5th Airborne pin box #5AB-E7920 fits in place of the Leland 7920 pin box which is 14 inches wide. The Wheel Masters Level #WM6780 has an adjustable bracket that will go up to 15-3/16 inches wide so it will fit!

view full answer...

Answer 5

The tongue of the trailer needs to be above the bed rails so that the trailer can turn correctly when making turns and going over bumps to clear the truck. I will attach a photo to help explain the clearances needed for your trailer.

view full answer...

Answer 6

I reached out to my contact at TST and confirmed that the TST TPMS - Color Display - Signal Booster - 6 Internal Tire Sensors #TST-507-INT-6-C you were looking at will work perfectly fine with the Counteract Balancing beads you use in your tires.…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

For some reason, some manufacturers decided it was a good idea to remove the pin box number from the label... which means the only way to figure it out is by calling them with the serial number or measuring your pin box to determine the one that you…

view full answer...

Answer 9

The Taskmaster Provider ST235/80R16 #PRG80235, like most trailer tires, are manufactured in China; these tires You could absolutely use an LT tire on your 5th wheel trailer as long as the LT in the tire size comes after the numbers and not before.

view full answer...

Answer 10

Yes, I was able to verify with Curt their Front Mount Trailer Hitch Receiver #C31078 will fit your 2024 Ford F-250 4 wheel drive.

view full answer...

What Is The Slotted Section In Bracket For Wheel Masters Level Master Trailer Bubble Level Used For?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching