Correct Mounting Brackets for CE Smith Single Axle Trailer Fenders

Question

Question:

I have Smith Plastic Trailer Fenders = CE19500-2. These fenders have 2.5 inch hole spacing. I need 2.5 inch spacing. What bracket do you have that meets this requirement

asked by: Paul

0

Expert Reply:

The correct mounting brackets for the CE Smith Single Axle Trailer Fenders part # CE19500-2 are the Mounting Brackets for Trailer Fender part # CE26061G-2. These brackets will line up with the pre-drilled holes in the fender.

expert reply by: Conner L

0

Answer 1

The Fulton Single Axle Trailer Fender #F008551 referenced in your question features overall dimensions of 7.35 inches wide, 21-1/2 inches long, and 6-1/2 inches tall. In order to determine if this will install on with your existing mounting brackets,…

view full answer...

Answer 2

The Fulton Fender #F008573 is plastic but it's a thick hard plastic fender. It has to be to support up to 300 pounds on the step. All the fenders we sell are either a similar plastic or metal. The fender has two mounting bracket slots in the…

view full answer...

Answer 3

The fender brackets we carry like the part #PF775-BKT-2 do have 3-1/2 inches between the mounting holes. These are the only ones we currently sell so to use them with the Fenders #F008541 you would either need to drill new holes in the brackets or…

view full answer...

Answer 4

The closest plastic fender to your current fenders that we carry is the Fulton Plastic Fender, #F008542, that you referenced. This fender measures 7-1/2 inches wide at the base and 6-3/8 inches wide at the top. It is 23-11/16 inches long and 8-11/16…

view full answer...

Answer 5

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 6

The difference between the 4.80-12 tire size you have now and the size 175/80-13 of the #AM3S130 you referenced is 4 inches overall in diameter and in width 2.2 inches. Judging by your pictures it doesn't look like you quite have the clearance…

view full answer...

Answer 7

The difference between the tire diameter you'd have now and a 14 or 15 inch trailer tire size would be about 6 inches. This would take up about 3 inches of your current fender to tire clearance so you'd need to make sure that wouldn't be…

view full answer...

Answer 8

Yes, there is a wider tire and wheel with a 4 on 4 pattern. It is the Taskmaster 5.30-12 Bias Trailer Tire with 12" Silver Mod Wheel item #TA66RR. The 5.30-12 tire has a section width of 5.3" and has a diameter of 21.9". This tire is a…

view full answer...

Answer 9

The Kenda trailer tire part #AM10130 that you referenced can fit all standard 12-inch trailer wheel sizes so it would work well on the 12-inch wheel you have on your Harbor Freight trailer.

view full answer...

Answer 10

Based on my research, the CE Smith Single Axle Trailer Fenders with Skirts #CE19500-2 that you referenced are very similar to the fenders you mentioned. The CE Smith fenders are designed to work with wheels 8 inches to 12 inches in diameter. Both…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Correct Mounting Brackets for CE Smith Single Axle Trailer Fenders

Products Referenced in This Question

Continue Researching