Is There Replacement Nut For 1991-1993 12,000 lb Bulldog Jack

Question

Question:

I purchased kit 500217 to rebuild my jack. Evidently it was built between 1991 and 1993 with the cast iron nut. The nut has 3 of 4 corners broken off. Is the nut a replacement item? What is the part number? If not how can I fix my jack? Thank you

asked by: Bruce S

0

Expert Reply:

I checked with Bulldog and there isn't a replacement nut alone for your 12,000 lb Bulldog jack built between 1991 and 1993. I'd love to give you an easy solution here but there isn't an option available to fix your jack, so the best we can do is a replacement jack.

Depending on what you need you can go with something like the Buyers Products Heavy Duty 4" Square Jack # 3370091410H.

I know it's not the solution you were looking for but it is the only option due to the nut not being available, so I've added a link to our entire selection of jacks if you want a different option.

expert reply by: Kyle S

0

Answer 1

We offer one replacement drop leg for a Fulton stabilizer jack. If you have a Fulton jack on your trailer this may work well for you. This is part #FSJ40324. I have attached a photo of this drop leg that has the dimensions noted you can check out.…

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Thanks for the information and photos, Brock! For your application I recommend picking up the 10K Square Direct Weld Jack - Drop Leg w/ Spring Return #TJD-12000SP-R2NH and reusing your current handle and crosstube. This is a weld-on installation but…

view full answer...

Answer 5

Basically you fill up the hub as much as you can through the hole in the cap like the part #RG04-300 and once the oil level is at the bottom of the cap hole it's as full as it needs to be.

view full answer...

Answer 6

I recommend the Kodiak Synthetic Bearing Oil for Oil Bath Hubs - 8 oz Bottle #XLPROLUBE. It is a 90 weight synthetic oil. Dexter bought out Kodiak so this meets their specifications. I've also attached a photo of Dexter's recommended Oil…

view full answer...

Answer 7

I have a number of dimensions for you of the Buyers Products Heavy-Duty 4" Square Jack w/ Side Pin Drop Leg - Sidewind - 26" Lift - 12K #3370091410H. It has a 4" square tube, an 8" x 8-1/2" foot pad, is 28" tall when it…

view full answer...

Answer 8

The Holland Binkley model 48,000 series jacks are very similar to the Bulldog Square Jack - Drop Leg w/ Spring Return #BD182815 which can utilize the Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity #BD1824200100. Your current…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Is There Replacement Nut For 1991-1993 12,000 lb Bulldog Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching