Cover For A 2016 Riverside Retro 195 Camper

Question

Question:

What is the best cover for my 2016 riverside retro RV model 195? It is rounded on both ends so wasn’t sure best option. Thanks in advance for the help!

asked by: Megan

1

Helpful Expert Reply:

For your 2016 Riverside Retro 195 I recommend Item # 290-52242. This cover that will provide plenty of protection while storing your camper in-between trips. It is compatible with 22', 23', and 24' campers. which is perfect for your camper.

expert reply by: Shane H

1

Answer 1

If you have a 2017 Toyota Tacoma with the tow package/factory 7-way yes it is pre-wired for a brake controller. For a brake controller I recommend the Prodigy P3 Brake Controller part #90195. This is our best selling brake controller because of how…

view full answer...

Answer 2

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 3

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 12

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Cover For A 2016 Riverside Retro 195 Camper

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching