Availability of 30 Inch Eye to Eye 6 Leaf Leaf Springs

Question

Question:

I am looking for spring pair for my 1950s Canned Ham trailer. 30 double eye 6 leaf 1 3/4w springs. UNA-022 is Universal part #. Also need new U bolt set

asked by: Russell L

1

Helpful Expert Reply:

We've just added the UNA-022 to our website using part # UG34FR. The springs have a 2500 lb capacity each or a 5000 lb per axle. The axle mounting hardware will depend on the diameter of your axle. I've linked to the U-bolt kits we offer.

expert reply by: Mike L

1

Answer 1

You can mount trailer axles above or below the leaf springs. The difference is just the amount of ground clearance that the trailer would end up having. The biggest advantage with the spring below the axle (trailer will be lower) is that you would…

view full answer...

Answer 2

The hitch ball angle adjustment on weight distribution systems is designed to provide more or less distribution of the tongue weight on your trailer hitch to the trailer and vehicle axles. If you adjust the ball angle farther away from the towing…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 5

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 6

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 7

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 8

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 9

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 12

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Availability of 30 Inch Eye to Eye 6 Leaf Leaf Springs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching