Solution For Carrying Bikes on Tear Drop Trailer Where 6" Drop Ball Mount Is Required
Question:
Im looking for a 6 Ball Mount that would allow the addition of a second receiver for a bike carrier. I was looking at the Curt Multipurpose Ball Mount, but it appears to only be available in a 2 . Are there any other similar options for towing a tear trailer and having a hitch mount bike carrier?
asked by: Donald C
Expert Reply:
I have a solution for you, and normally the Curt Multipurpose Ball Mount # D210 would be the best solution for this since it wouldn't reduce the tongue weight capacity of your hitch. I don't recommend any type of dual receiver with a drop because doing so would reduce the tongue weight capacity of your hitch by roughly 50%, so that would limit you quite a bit.
If you've got a tear trailer with a straight tongue then I recommend using the Hitch-It 2 Bike Rack for Straight Tongue Trailers # LC731138 or if you've got an A frame trailer with a jack mounted at the front then the Jack-It 2 Bike Rack for A-Frame Trailers - 22-1/2" Jack Clearance # LC429756 would both be good options.
If you need to carry 4 bikes, then the best available solution for this would be using the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 5" Drop/Rise - 16K # 325-GH-214, which would allow you to carry a bike rack and gives you a ball mount for your tear drop trailer. This is a 5" drop, but if you needed something larger then next size down is a 7-1/2" drop with the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 7-1/2" Drop/Rise - 10K # 325-GH-314.
Products Referenced in This Question
Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 5" Drop/Rise - 16K
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 2 Inch Ball
- 2-5/16 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gray
- Drop - 5 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 16000 lbs GTW
- Stacked Receivers
- Gen-Y Hitch
more information >
Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 7-1/2" Drop/Rise - 10K
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 2 Inch Ball
- 2-5/16 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gray
- Drop - 7 Inch
- Rise - 7 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Stacked Receivers
- Gen-Y Hitch
more information >
Continue Researching
- Article: How to Carry Bikes While Towing a Travel Trailer
- Q&A: Bike Rack Recommendation for NuCamp 320 Camper
- Q&A: Recommended AC With Heat Strip for Enclosed Trailer
- Article: Trailer Wiring Diagrams
- Q&A: Bike Rack Solution for Carrying Bikes between Tow Vehicle and Camper
- Q&A: Straight Stinger for Jack-It 2 Bike Rack for A-Frame Trailers
- Q&A: Orientation of Jack-It 2 Bike Rack for A-Frame Trailers Installed on Camper Trailer
- Q&A: Fitment of the Hitch-It 2 # LC731138 to a 10" Straight Trailer Tongue
- Q&A: Converting a Hymer Touring GT Camper from Surge to Electronically Controlled Brakes
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: Determining Trailer Tongue Weight
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps