Availability of Grease Cap that Fits Bore of 2.43 inch

Question

Question:

What size bearing seal do I need for a brake drum that the inside bore measures 2.43 ID? Not talking about the outside cap, which is 2.043 ID. I need a seal for the large inner bearing.

asked by: Brent C

0

Expert Reply:

Are you maybe asking about the grease cap? I believe you are since a very common size is 2.44 inch like the part # RG04-080.

expert reply by: Jameson C

0

Answer 1

Hello Robert, sorry to hear the seals you got did not work. Being that this trailer is so old, I am not surprised to hear that finding replacement parts has been difficult. Looking thru all of the seals we carry, I do not find an exact match, but…

view full answer...

Answer 2

We have the individual parts you need but not as a kit. You'd want the bearing part #LM67048 and #L68149. Since this is not a standard bearing combination I would need to know more info to pick out the seal. I'd need to know the…

view full answer...

Answer 3

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Availability of Grease Cap that Fits Bore of 2.43 inch

Product Page this Question was Asked From

Continue Researching