Will etrailer Hitch Lock # e98882 Fit Hitch Tube that Measures 2-5/8 inches Outer Diameter

Question

Question:

My hitch receiver outside measurements are 2 5/8 square. Will lock # e98882 work for this application?

asked by: Doug H

1

Helpful Expert Reply:

The usable span of the hitch lock part # e98882 is exactly 2-5/8 inches which matches what you have so it will fit and work great.

expert reply by: Jameson C

1

Answer 1

On the Nissan Frontier and other Nissan vehicles, if the vehicle did not come with a factory tow package it will not have a functioning wiring harness even if one, like #118263, is added. There will be relays that will need to be inserted to make the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 9

From what I can find on the 2022 Nissan Frontier, the plug for the brake controller that will let you use a harness like the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers #3050-P is located just above the OBD connector, taped tight…

view full answer...

Answer 10

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

The best solution is to purchase the Swagman Bike Frame Adapter Bar for Electric, Step Through, and Cruiser Bikes #S57FR for the non-electric women's bike and any electric bike that has a step-through or alternative frame. The adapter bar will…

view full answer...

Will etrailer Hitch Lock # e98882 Fit Hitch Tube that Measures 2-5/8 inches Outer Diameter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching