How Does Replacement Nut Retainer and Nut for Yakima HoldUp Bike Carrier # Y90254 Install

Question

Question:

How does this part work? There is no directions on this?

asked by: Jeff

0

Expert Reply:

Basically you just push the Replacement Nut Retainer and Nut for Yakima HoldUp Bike Carrier # Y90254 into the shank of the bike rack and the pins will line up with the indentations in the shank so that the nut is held at the right location when threading in the hitch pin.

expert reply by: Jameson C

0

Answer 1

Yes! We do have those parts for your Yakima SwingBase #Y34VR. The replacement parts you need the Replacement Anti-Rattle Hitch Bolt and Washer for Yakima HangOver Bike Rack #Y52FR (Yakima part 8880953) and the Replacement Hitch Bolt Threaded Insert…

view full answer...

Answer 2

Correct, you are indeed missing a very critical component of the Yakima SwingDaddy 8002464, the wedge mechanism. Now, I have good news and bad news for you. The good news is that we have what you need to get the rack functional again but the bad news…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

How Does Replacement Nut Retainer and Nut for Yakima HoldUp Bike Carrier # Y90254 Install

Product Page this Question was Asked From

Continue Researching