Will Rhino-Rack RR43157 Hi-Lift Jack/Shovel Holder fit T Slots on Yakima LockNLoad Platform

Question

Question:

Will this mount on a locknload platform from Yakima

asked by: Jeff C

0

Expert Reply:

The T-slots used by the Rhino-Rack Pioneer Platform and the Yakima Lock N Load are the same dimension, so the # RR43157 Rhino-Rack Hi-Lift Jack/Shovel Holder should work fine on the Yakima Lock N Load.

expert reply by: Mike L

0

Answer 1

The Replacement M10 Channel Nut for Rhino-Rack Accessories #RR89TB has a M10 thread size and base dimensions of 35mm x 19mm x 8mm.

view full answer...

Answer 2

The channels on top of the Yakima LockNLoad Platform Rack for Crossbars like the part #Y05045-39 are designed to accommodate roof rack accessories that were designed to attach to crossbar top channels. So basically any track nut designed for roof…

view full answer...

Answer 3

The T-Slots on the Yakima LockNLoad Platform Rack #Y05044-39 have the same dimensions as standard crossbars so you can basically use any brand of T-Bolts to accomplish your job. For example, you can use the Thule Square T-Bolt #853208914 or the…

view full answer...

Answer 4

I have an answer for you. I reached out to my contact at Yakima and they said that they specially make t-slot hardware for accessories that are designed to fit into LockNLoad Platforms like the #Y05044-39. With that being said, there is no way to…

view full answer...

Answer 5

I pulled this from our warehouse and it was a lot smaller than I originally thought. In the attached picture I have all of the dimensions you requested noted. To give you a quick overview of the dimensions: Thickness - .16 inches Long Sides - .993…

view full answer...

Answer 6

I have a complete kit as a solution with Thule but unfortunately the Rhino Rack Aero Crossbars like part # RRVA106B-2 will not work with the Thule Rapid Podium Feet. There is enough of a difference that there is no way to guarantee the weight ratings…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 11

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Will Rhino-Rack RR43157 Hi-Lift Jack/Shovel Holder fit T Slots on Yakima LockNLoad Platform

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching